What specialist testing can show
TI-5000JX bench. Mitchell documents Generic Incremental AB quadrature. Confirm the fitted pulse count and startup signals.
TI-3000JX motor run. Exact motor-run setup open.
Starting lead. Exact lead open. Match the fitted connector to a documented drawing.
Sanyo Denki INC-E Wire-Saving Incremental Encoder technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| INC-E | Wire-saving incremental type described by Mitchell. Capture the full motor and encoder labels to establish the fitted variant. |
| 2,000- and 6,000-period versions | Two documented examples. Confirm the fitted count from the source or the supported count test. |
| ABSOSYN serial families | Different feedback types, including the E07B and R11 guides. Do not infer their retention or data wiring from an INC-E connector. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Startup state | The shared outputs initially carry commutation information. |
| Running feedback | Complementary A/B quadrature and Z reference on the documented wire-saving arrangement. |
| Count examples | 2,000 or 6,000 periods per turn gives 8,000 or 24,000 four-edge counts. Use the value for the fitted label. |
Interface and measuring method
At startup the drive interprets the shared channels as UVW. Once the encoder transitions to position feedback it uses the A/B phase relationship and the Z reference. Observe startup and running behavior separately in the correct fixture.
Mounting and fit
Confirm the motor and encoder order before comparing mounting depth, shaft arrangement and coupling. Preserve connector routing and the original phase relationship on the fitted motor.
Wiring and connector scope
Identify the true and complement pairs from the exact motor drawing. Avoid assigning a line from a static reading alone because its function depends on startup state. Check continuity only with the harness disconnected.
Internal motor and machine cables
The INC-E selection documents the method. Match the exact Mitchell harness and machine cable to the fitted connector and motor order before using a pin table.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Initial states look like static signals | Check the expected startup interval before judging the A/B outputs. Verify the serial or incremental type from the label. |
| Motor starts and then loses position | Check the transition into A/B/Z, cable integrity and count setting. Inspect the coupling and index path separately. |
| Measured count is four times the label number | Distinguish waveform periods from decoded quadrature edges. Compare the controller and tester counting conventions. |
Angle of alignment and commissioning
Record startup state and reference behavior with the correct profile. Preserve the incoming physical position and verify commutation using the applicable motor procedure after installation.
Motor and drive applications
Sanyo Denki servo motors fitted with INC-E
Avoid treating startup commutation on shared lines as a wiring short or failed quadrature channel.
Related SpareFaber guides
Drawings, pin maps and manuals
- Sanyo Denki Motors and Serial Encoders. Types Supported and INC-E subsection. Separate startup UVW states from running ABZ signals.
- Sanyo Denki P-series technical report. OEM context for wire-saving incremental feedback on the documented P-series platform. Use the fitted motor drawing for pin numbers.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.