What specialist testing can show
TI-5000JX bench. Check the EnDat model and its 1 Vpp channels using the E-option drawing.
TI-3000JX motor run. Use the appropriate Siemens EnDat motor-run selection only after confirming fitted encoder and poles.
Starting lead. TI-5031 on the documented Siemens EnDat motor connection. Confirm the fitted plug. Module TI-5101 only for the documented compatible 1 Vpp test path.
Siemens SIMOTICS S-1FK7 G2 E AM2048S/R EnDat Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| S-1FK7 G2 E option | Siemens uses the E character in the encoder position for the AM2048S/R EnDat version in the replacement manual. |
| AM2048S/R-72 · 6FX2001-5JE04-1QA0 | Siemens service part for the 1FK703 frame listed in the table. |
| AM2048S/R-88 · 6FX2001-5JE04-1DA0 | Siemens service part for listed 1FK704, 1FK706, 1FK708 and 1FK710 frames. Verify the complete order. |
| 6FX2001-5JE20-2DA1 | Older Siemens article in the replacement manual. Follow the replacement table and fitting sequence. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Feedback | AM2048S/R absolute EnDat with a round M23 connector for the documented E option. |
| Analogue scale | Siemens describes 2,048 signals per revolution for the AM2048S/R designation. Verify the actual part and interpretation. |
| Mechanical scope | -72 and -88 are distinct assembly variants. The OEM procedure includes different frame applicability and replacement details. |
| Interface boundary | The manual has separate tables for the EnDat, sin/cos incremental and DRIVE-CLiQ options. |
Interface and measuring method
The receiver reads absolute position through EnDat and can use the applicable sine/cosine channels for fine motion. A good serial reply and poor analogue quality are different conditions. Check the fitted option and signal paths separately.
Mounting and fit
Use the Siemens encoder replacement manual’s E-option frame table and the matching -72 or -88 installation sequence. Record the fitted spindle engagement, adapter and connector geometry before removal.
Wiring and connector scope
Use the Siemens round-plug drawing for the exact E-option unit and the fitted drive. Confirm the connector key and view. Identify serial clock/data and the analogue channels from the matching OEM drawing.
Internal motor and machine cables
Match the Siemens signal cable assembly to the complete motor and drive orders. The TI-5031 starting connection belongs to the verified Siemens EnDat test arrangement. Check the fitted motor and approved fixture before using it.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Serial response present but the drive faults during travel | Check analogue signal quality, connector strain and the complete machine cable. |
| Wrong part appears to fit the motor | Match the complete motor frame and the -72 or -88 service number from the table. |
| Fault follows a connector or drive change | Verify the E feedback option, drive input and cable assignment before testing the encoder. |
Angle of alignment and commissioning
Capture the incoming reference and encoder information. Use the Siemens replacement and commissioning procedure for the exact frame and service part. Verify motor operation, zero and any required control checks after fitting.
Motor and drive applications
SIMOTICS S-1FK7 G2, E encoder option
Decode the E character and choose the 72 or 88 frame-dependent M23 spare.
Related SpareFaber guides
Drawings, pin maps and manuals
- Siemens Motors. Overview, 1FK7 with supported HEIDENHAIN EnDat feedback
- Siemens S-1FK7 G2 encoder replacement manual. E option M23 selection, -72/-88 frame-specific spares and fitting procedures.
- Mitchell HEIDENHAIN serial encoder chart. Siemens EnDat fixture and analogue test scope.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.