What specialist testing can show
TI-5000JX bench. Use the TI-5000JX TS5778 serial reference with the verified Shinko connector and actual encoder configuration.
TI-3000JX motor run. Mitchell documents Shinko eight-pole 8,192 and 16,384 count run selections. Confirm actual count and the complete approved fixture.
Starting lead. TI-5035 for the documented Shinko branch.
Shinko V21145018 Tamagawa OAH74–TS5778 Servo Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| Shinko V21145018 | Motor example recorded by Mitchell as 4 kW and 3,000 rpm. Verify the fitted encoder label and run profile. |
| Shinko V211462002 | Second cited Shinko example, 2 kW and 3,000 rpm. This does not assign a count profile to either motor. |
| OAH74 TS5778 | Feedback label reported by Mitchell. Compare the complete suffix and measured count before selecting the profile. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Feedback | Tamagawa TS5778 SmartABS on the documented Shinko application. |
| Run profiles | Eight-pole setups with 8,192 or 16,384 incremental counts per revolution. Verify the fitted count. |
| Starting lead | TI-5035 on the documented Shinko branch. The chart separately identifies TI-5666 for Kobelco robot motors. |
Interface and measuring method
The matched fixture reads serial data and checks incremental feedback for the run setup. Verify direction and count before interpreting commutation. The serial family and common connector alone do not establish which count profile the motor uses.
Mounting and fit
Secure the load and follow the original motor procedure before removing any cover. Capture the motor plate, encoder sticker, fitted seat and cable exit. Verify the rear assembly drawing before setting mechanical position or fastener torque.
Wiring and connector scope
Use the Mitchell Shinko support table and the matching TI-5035 cable sheet, then compare the actual plug and circuits. Keep the similar Kobelco harness separate unless its own connector and wiring are verified.
Internal motor and machine cables
TI-5035 is the Shinko tester lead. Obtain the exact internal loom and machine cable from the fitted motor and controller labels. For any approved repair, compare both connector views and the shield bond.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Count is about double or half the expected value | Check the two Shinko profiles and verify the fitted count before changing the encoder. |
| No data at the motor plug | Inspect connector seating and trace the isolated harness. Verify the Shinko versus Kobelco lead and serial selection. |
| Serial data reads but the motor will not run properly | Verify commutation and incremental count with the supported Shinko fixture. Check the machine reference and drive alarms separately. |
Angle of alignment and commissioning
Retain the original reference and wiring record. A qualified specialist should verify the matched eight-pole profile, direction, count and commutation on the proper fixture. Any robot or machine reference needs its own OEM procedure.
Motor and drive applications
Shinko V21145018 and cited comparison motor V211462002
Record the exact TS5778 suffix, motor connector view, fitted count and original Shinko machine cable.
Related SpareFaber guides
Drawings, pin maps and manuals
- Shinko Motors. Identification and Feedback Type Selection
- Mitchell Shinko supported types and cables. Both OAH74 profiles use TI-5035 on the documented Shinko branch.
- Mitchell Tamagawa Serial Encoders. Tamagawa bench testing and serial device identification.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.