What specialist testing can show
TI-5000JX bench. Read the verified EnDat feedback. Confirm memory procedure for the actual assembly with Mitchell.
TI-3000JX motor run. Exact run selection and memory alignment case remain to be verified for the fitted motor.
Starting lead. TI-5083 on the documented 17-contact M23 EnDat branch.
Beckhoff AM302x–AM304x EnDat option EnDat Servo Motor Feedback technical reference
Find your part number
Compare the fitted feedback label, complete motor order and connector. A motor order and an encoder MPN identify different items.
| ID or order | How to identify it |
|---|---|
| AM302x–AM304x with ECN 1113 | Beckhoff manual lists this as the singleturn EnDat option for these frames. |
| AM302x–AM304x with EQN 1125 | Beckhoff lists this for multiturn EnDat in the same frame range. |
| Resolver, BiSS or HIPERFACE | Other AM3 feedback options. Match the motor label and the actual interface before applying the EnDat drawing. |
Production and end-of-life status
Confirm orderability and any replacement with the manufacturer against the full fitted ID. The linked documents identify the documented setup.
Specifications
| Parameter | Verified scope |
|---|---|
| Within-turn position | ECN 1113 is the singleturn device in the stated Beckhoff feedback table. |
| Turn information | EQN 1125 is the corresponding multiturn option. Verify the exact HEIDENHAIN ID for detailed data. |
| Starting Mitchell lead | TI-5083 for the documented EnDat 17-contact M23 connection. |
| Mechanical option | Beckhoff states motor length depends in part on the fitted feedback unit. Use the frame and feedback-specific outline. |
Interface and measuring method
The drive reads position through EnDat. Use the fitted encoder’s analogue and serial configuration when assessing feedback. Verify turn information separately on the multiturn assembly.
Mounting and fit
Use the Beckhoff AM3000 frame outline and the actual HEIDENHAIN ID for the encoder seat and shaft interface. Preserve the incoming mechanical position and fitted connector arrangement.
Wiring and connector scope
Use the Beckhoff manual’s AX5000 or AX2000 EnDat wiring section for the applicable drive. Verify the motor-side connector against the 17-contact TI-5083 branch before testing.
Internal motor and machine cables
Select the Beckhoff feedback cable by motor and drive connection. For an internal harness, match the exact ECN or EQN connector and motor assembly. Keep the direct and motor-side maps separate.
Fault checks
Use the site’s isolation procedure before opening a connector or checking resistance. Secure the load against motion, lock out relevant energy sources, wait the specified discharge time and have a qualified technician verify isolation. Follow the OEM procedure for any retention battery.
What can I check on the machine?
Disconnect the harness at both ends. Check end-to-end continuity against the exact drawing, then check for unintended shorts between conductors and to the shell or shield. Compare against the documented shield bonds. Inspect pins, keying, debris, moisture and latch engagement. Check clamps or fasteners only where accessible under the approved procedure.
Use only the OEM-approved powered check and a suitable breakout. A qualified technician can compare the voltage across the specified supply and return with the model’s limits under the stated test conditions. A multimeter can check supply health. Signal integrity and communications require the appropriate signal test.
| Symptom | What to verify |
|---|---|
| Angle reads but turns do not | Check whether the fitted encoder is ECN 1113 or EQN 1125 and the drive’s configured mode. |
| No response on AM3 connector | Verify the actual feedback option and matching connector view before using TI-5083. |
| Replacement fits and drive rejects it | Check the exact OEM order, original data and compatible firmware. |
Angle of alignment and commissioning
Record the motor and encoder order and any stored information. Mitchell asks for confirmation on reading and programming the fitted Beckhoff option. Verify position, direction and the original reference before recommissioning.
Motor and drive applications
Beckhoff AM302x–AM304x
Distinguish ECN 1113 singleturn and EQN 1125 multiturn from other AM3 feedback options.
Related SpareFaber guides
Drawings, pin maps and manuals
- Beckhoff AM Series Motors. AM3 options and common AM2/AM3 EnDat test cable
- Beckhoff AM3000/AM3500 technical documentation. Feedback unit table and separate AX5000 and AX2000 EnDat connection drawings.
Questions
Can I use a similar label as a replacement?
Compare the interface, mechanical fit, connector, data or commutation requirements and OEM option before choosing a substitute. The ID table gives the useful distinctions for this guide.
What information helps with a diagnosis?
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.
Site visit or send-in evaluation
Send the encoder and motor labels, drive model, alarm history and both connector views. Say whether the problem began after cable work, encoder replacement or a drive change. We can confirm visit scope or send-in evaluation and timing from those details.